Amplifier(s) for your Auto. Get JL and your going to be very plaesed!!!I'm over 50 and have always liked music, and loud, not deafening. My first auto amplifier was over 35 years ago.Quality is the most important part of my listening pleasure. Deffinately worth the time and dime!I have been in the car audio scene for over 20years and have had experience with crappy as well as top of the line products.I was wanting to do an install in my Jeep Cherokee for about a year and decided to do a budget install but knew I wouldn't be happy with subpar equipment so I looked to some upper name brand components and decided to try an entry level JLAudio amplifier.
All I can say is that for the low cost it is an incredible amplifier!I have tested and abused this amp over the last month or so and don't have any complaints. Glary utilities pro free download with serial license key. It is a very user friendly straight forward amp with enough power for any system besides a competition you could ask for. And realistically I'd compete with it pushing my fronts any day!Very accurate and clean sound is all I've experienced with it pushing 2 sets of Morel components up front.Couldn't be happier.Verified purchase: No.
.For maximum performance, we highly recommend that you have your new amplifier installed by an authorized JL Audio dealer. Your authorized dealer has the training, expertise and installation equipment to ensure optimum performance from this product.(pg. 9) Filter Input Filter Input Filter Mode Filter Mode Frequency Sensitivity Frequency Sensitivity Selector Selector Control Control Control Control (pg. 8) JL Audio.Check before drilling any holes in your vehicle The outer shell of your JL Audio amplifier is to make sure that you will not be drilling designed to remove heat from the amplifier through a gas tank, brake line, wiring harness or circuitry.6) Find a good, solid metal grounding point The JX360/4 can be operated with a wide close to the amplifier and connect the variety of source units and system configurations.
Jl Audio Jx360/4 Manual Online
Negative power wire to it using appropriate For detailed specifications, please refer to hardware.If the amplifiers as possible and should connect to the JX360/4 is the only device connected to this main JX360/4 with 4 AWG power wire. Wire, use a 50A AGU or MAXI® fuse (no other fuse is required in this situation).The JX360/4 is turned on and off The JX360/4’s has two input sections: one for Channels 1&2 and another for Channels 3&4. On lead, typically controlled by the These input sections allows you to send signals to source unit’s remote turn-on output.“Input Mode” Switch If you wish to send four discrete channels of input into the JX360/4, simply use all four inputs (Channels 1 & 2 and Channels 3 & 4) and set the “Input Mode” switch to “4 Ch.”.Appendix A (page to one or both of the JX360/4’s channel pairs in 12). Doing so will result in audible distortion a bi-amplified system.This pass-through pre-amp output or both of the JX360/4’s channel pairs in a delivers a summed stereo signal, combining the bi-amplified system.
2) “Filter Freq. (Hz)” A simple rotary Signal and the Ch.1) Left Channel Only or Right Channel Only the amplifier to enter a protection mode. Information: If you wish to send a left-only or right-only signal to a pair of the JX360/4’s channels, use a “Y-Adaptor” to split the single Bridging is the practice of combining the.JL Audio dealer so control panel of the amplifier. That it may be sent in to JL Audio for service. There are no user serviceable parts or fuses inside the amplifier.
The unique nature of the circuitry in the JL Audio amplifiers requires specifically trained service personnel.(within the frequency range to be amplified) at 3/4 source unit volume. 7) Connect the AC voltmeter to the speaker output connectors of the amplifier. Make sure you test JL Audio.Recommended Fuse Value (Type): 50A (MAXI or AGU) Minimum Copper Power/Ground Wire Gauge: 4 AWG 15.40' x 7.68' x 2.15' (391 mm x 195 mm x 55 mm) 8.75 lbs.
(3.97 kg) Due to ongoing product development, all specifications are subject to change without notice. JX360/4.Check the input connectors to ensure that they all are making good contact with the input jacks on the amplifier. JL Audio.The speaker wire connectors are designed to accept up to 8 AWG wire. Make sure to strip the wire to allow for a sufficient connection with the metal inside the terminal block. Disable windows 10 tiles.
JX360/4.Use this diagram to document your amplifier’s switch and control positions. JL Audio JX360/4.JL Audio warrants this product to be free of defects in materials and workmanship for a period of one (1) year from the original date of purchase. This warranty is not transferrable and applies only to the original purchaser from an authorized JL Audio dealer.
In installed an amp a month ago (JL JK360) and it worked fine the first 2 times on the water. This weekend, I turned it on. And it immediality went into protected mode. Looking at the manual I see:'Protect” (Red): Indicates that the amplifierprotection circuitry has been activatedto prevent product failure due to thermaloverload, short-circuit or a dangerouslylow impedance connected to the amplifieroutputs. Connecting the speaker outputsto an impedance lower than 2 ohms stereo(4 ohms bridged) will cause this protectionmode to activate. When this protection modeis activated, the amplifier will shut down toprotect its circuitry.
When the problem iscorrected, the amplifier will return to normaloperation and the “Protect” LED will shut off.' How do I go about fifguring out the issue? Is it disconnecting the speakers? Are there other places to look?Thanks in advance. In installed an amp a month ago (JL JK360) and it worked fine the first 2 times on the water.
Jl Audio Jx360/4 Manual 1
This weekend, I turned it on. And it immediality went into protected mode. Looking at the manual I see:'Protect” (Red): Indicates that the amplifierprotection circuitry has been activatedto prevent product failure due to thermaloverload, short-circuit or a dangerouslylow impedance connected to the amplifieroutputs. Connecting the speaker outputsto an impedance lower than 2 ohms stereo(4 ohms bridged) will cause this protectionmode to activate. When this protection modeis activated, the amplifier will shut down toprotect its circuitry.
6.5 Jl Audio Speakers
When the problem iscorrected, the amplifier will return to normaloperation and the “Protect” LED will shut off.' How do I go about fifguring out the issue? Is it disconnecting the speakers? Are there other places to look?Thanks in advance.If everything worked fine and now it doesnt then this is the route id use to check my problem.1.
Make sure the batteries are completly charged.2. Make sure all your connections are tight at the ampFor all connecting and disconnecting i reccomend you turn off the Deck to prevent shorting.3. Unplug both RCAs into the amp, if amp works then you have bad RCA or the Deck output has an internal short.Problem still there proceed.Replug in the RCAs.4.
Comments are closed.
|
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |